Skip to content

Dead Pixel Test — Full-Screen Monitor Test for Dead and Stuck Pixels

Full-screen colours, gradients, backlight-bleed and sharpness screens, a stuck pixel flasher, refresh rate and PPI.

Found a problem, or something that could be better? We read every message and we fix things quickly.

This dead pixel test fills your screen with solid colours so dead or stuck pixels stand out: a dead pixel shows as a dark dot on white and the bright colours, a stuck pixel as a red, green, blue or white dot on black. Press Start, then click, tap, swipe or use the arrow keys to step through black, white, red, green, blue, cyan, magenta, yellow and greys, and press Esc to leave. The same viewer has banding gradients, a dim-grey screen for backlight bleed and IPS glow, and a sharpness screen with 1-pixel lines and small text.

Below the test, the page shows what your browser reports about the display (CSS resolution, device pixel ratio, an estimate of the physical pixels, colour gamut and HDR support) and measures the refresh rate from animation frames. A PPI estimator turns your resolution and diagonal into pixel density and dot pitch. There is also a stuck pixel flasher you can drag over a suspect spot; it sometimes frees a stuck pixel and cannot fix a dead one, and it only starts after you accept a photosensitivity warning. Everything runs in your browser; nothing is uploaded.

How to use

  1. Clean the screen first: dust looks like a dead pixel. Set brightness to normal, and for the bleed test, darken the room.
  2. Press "Start full-screen test". The screen turns black.
  3. Look over the whole screen, corner to corner, then click, tap, swipe left or press → or Space for the next colour. ← or a swipe right goes back. Press A to cycle automatically.
  4. A dot that stays dark on white is a dead pixel; a dot that stays lit on black, or shows on only some colours, is a stuck pixel. Note where it is.
  5. On the gradient screens, look for wide flat bands or colour tints; on the dim grey screen, look for bright patches at the edges (backlight bleed or IPS glow).
  6. Press Esc (or Exit) to leave. To try the flasher on a stuck pixel, read the warning, tick the consent box, start it and drag the square over the pixel for 10–20 minutes.

Frequently asked questions

What is the difference between a dead pixel and a stuck pixel?

A dead pixel gets no power and stays black, so you see it as a dark dot on white or bright colours. A stuck pixel has one or more sub-pixels (red, green or blue) that stay on, so it shows as a coloured or white dot on black and on colours that do not include that sub-pixel: a pixel stuck on red is visible on the green and blue screens but blends into the red one. A "hot" pixel stays fully white. Stepping through every solid colour is how you tell them apart.

Can a dead pixel be fixed?

A truly dead pixel usually cannot be fixed by software, because its transistor no longer switches. A stuck pixel sometimes recovers after rapid flashing (what the flasher on this page does) or, on some LCDs, after gentle pressure with a soft cloth while the screen is off, which can also damage the panel, so try that at your own risk. If you find a defect on a new screen, check the seller’s and maker’s pixel policy and return window first; many manufacturers allow a certain number of defective pixels before they replace a panel.

Is the stuck pixel flasher safe?

It flashes rapidly, which can trigger seizures in people with photosensitive epilepsy, so the page shows a warning and starts the flasher only after you tick a consent box. The flashing area is a small square (40 to 200 CSS pixels), not the whole screen, and a slow mode changes colour twice per second, below the three-flashes-per-second guideline. If your device is set to reduce motion, the flasher starts in slow mode. Look away while it runs. It will not harm the screen.

How do I test for backlight bleed or IPS glow?

Darken the room, set the brightness you normally use, and open the black and dim grey (5%) screens. Backlight bleed shows as bright patches along the edges or corners that stay put when you move your head; IPS glow is a silvery or warm glow in the corners that changes with viewing angle. Some glow is normal on IPS panels; strong uneven bleed at normal brightness is worth reporting. Phone cameras exaggerate both, so judge with your eyes.

How accurate is the refresh rate and resolution information?

The refresh rate is measured from the browser’s animation frames: usually the panel’s rate, but battery saver, a background tab or variable refresh rate can lower it, and some browsers cap it. The resolution is what the browser reports in CSS pixels multiplied by the device pixel ratio; with display scaling, that can differ from the panel’s native resolution. Colour gamut and HDR come from CSS media queries, which describe what the browser believes, not a measurement of the panel.

How is PPI calculated?

Pixels per inch is the diagonal in pixels divided by the diagonal in inches: √(width² + height²) ÷ diagonal. A 24-inch 1920 × 1080 monitor is √(1920² + 1080²) ÷ 24 ≈ 91.8 PPI; a 27-inch 2560 × 1440 monitor is about 108.8 PPI; a 27-inch 4K monitor about 163.2 PPI. Dot pitch is 25.4 mm divided by the PPI. Use the native resolution and the advertised diagonal; diagonals are rounded, so the result is approximate.

What each test screen shows

• Black: stuck and hot pixels (lit dots), backlight bleed and glow at the edges.

• White: dead pixels (dark dots), dust and dirt, colour tint and uneven brightness.

• Red, green, blue: which sub-pixel is faulty. A sub-pixel stuck on shows on the two other primaries; one stuck off shows as a dark dot on its own colour.

• Cyan, magenta, yellow: confirm a stuck sub-pixel (a red-stuck pixel turns white on cyan).

• Greys: uniformity, vignetting and tint shifts across the panel, and dirty screen effect on large TVs.

• Dim grey (5%): clouding, backlight bleed and IPS glow, which pure black can hide on some panels.

• Ramps: banding and crushed shadows; the sharpness screen: scaling blur, ClearType/subpixel fringing and focus.

Reading the gradient (banding) tests

The 8-bit grey ramp has 256 bands, one for each grey level from 0 to 255, drawn pixel-exact rather than with a browser gradient. On a good 8-bit path you see a nearly smooth ramp; wider flat bands mean levels are being merged, typically by a 6-bit panel without good dithering, an aggressive colour profile, a night-light filter or a "dynamic contrast" mode. The 32-step half below should show 32 clearly separate, evenly spaced steps; if the first few dark steps look identical, shadows are being crushed (try the brightness or black level setting).

The red, green and blue ramps show banding or colour tint per channel, and the smooth gradient is drawn by the browser, which some browsers dither, so compare it with the stepped ramp rather than judging it alone. Banding that appears only in the browser and not in other apps usually comes from the colour management or GPU driver, not the panel.

Checking a new monitor, TV or phone

Test as soon as you unpack it, because return windows are short. Let the screen warm up for a few minutes, clean it, and step through every solid colour slowly from corner to corner; a single dead pixel is easiest to see on white and on the primaries. On a TV, open this page in its built-in browser or cast a browser tab, and check the dim grey screen in a dark room for clouding.

Take notes and a photo with the pixel’s position (a coin or ruler for scale helps) before you contact the seller. Manufacturers’ pixel policies differ: some replace a panel for a single bright pixel, others only above a count or within a zone, so check the exact policy for your model.